Vfrdtyky

Thermodynamics
The classical Carnot heat engine
Branches Classical Statistical Chemical Quantum thermodynamics Equilibrium / Non-equilibrium
Laws Zeroth First Second Third
Systems State Equation of state Ideal gas Real gas State of matter Equilibrium Control volume Instruments Processes Isobaric Isochoric Isothermal Adiabatic Isentropic Isenthalpic Quasistatic Polytropic Free expansion Reversibility Irreversibility Endoreversibility Cycles Heat engines Heat pumps Thermal efficiency
System properties Note: Conjugate variables in italics Property diagrams Intensive and extensive properties Process functions Work Heat Functions of state Temperature / Entropy (introduction) Pressure / Volume Chemical potential / Particle number Vapor quality Reduced properties
Material properties Property databases Specific heat capacity  c={displaystyle c=} T{displaystyle T} ∂S{displaystyle partial S} N{displaystyle N} ∂T{displaystyle partial T} Compressibility  β=−{displaystyle beta =-} 1{displaystyle 1} ∂V{displaystyle partial V} V{displaystyle V} ∂p{displaystyle partial p} Thermal expansion  α={displaystyle alpha =} 1{displaystyle 1} ∂V{displaystyle partial V} V{displaystyle V} ∂T{displaystyle partial T}
Equations Carnot's theorem Clausius theorem Fundamental relation Ideal gas law Maxwell relations Onsager reciprocal relations Bridgman's equations Table of thermodynamic equations
Potentials Free energy Free entropy Internal energy U(S,V){displaystyle U(S,V)} Enthalpy H(S,p)=U+pV{displaystyle H(S,p)=U+pV} Helmholtz free energy A(T,V)=U−TS{displaystyle A(T,V)=U-TS} Gibbs free energy G(T,p)=H−TS{displaystyle G(T,p)=H-TS}
History Culture History General Heat Entropy Gas laws "Perpetual motion" machines Philosophy Entropy and time Entropy and life Brownian ratchet Maxwell's demon Heat death paradox Loschmidt's paradox Synergetics Theories Caloric theory Theory of heat Vis viva ("living force") Mechanical equivalent of heat Motive power Key publications "An Experimental Enquiry Concerning ... Heat" "On the Equilibrium of Heterogeneous Substances" "Reflections on the Motive Power of Fire" Timelines Thermodynamics Heat engines Art Education Maxwell's thermodynamic surface Entropy as energy dispersal
Scientists Bernoulli Boltzmann Carnot Clapeyron Clausius Carathéodory Duhem Gibbs von Helmholtz Joule Maxwell von Mayer Onsager Rankine Smeaton Stahl Thompson Thomson van der Waals Waterston
Book Category Thermodynamics Portal
v t e

In thermodynamics, the thermal efficiency (ηth{displaystyle eta _{rm {th}}}) is a dimensionless performance measure of a device that uses thermal energy, such as an internal combustion engine, a steam turbine or a steam engine, a boiler, furnace, or a refrigerator for example. For a heat engine, thermal efficiency is the fraction of the energy added by heat (primary energy) that is converted to net work output (secondary energy). In the case of a refrigeration or heat pump cycle, thermal efficiency is the ratio of net heat output for heating, or removal for cooling, to energy input (the coefficient of performance).

Overview

Output (mechanical) energy is always lower than input energy

In general, energy conversion efficiency is the ratio between the useful output of a device and the input, in energy terms. For thermal efficiency, the input, Qin{displaystyle Q_{rm {in}}}, to the device is heat, or the heat-content of a fuel that is consumed. The desired output is mechanical work, Wout{displaystyle W_{rm {out}}}, or heat, Qout{displaystyle Q_{rm {out}}}, or possibly both. Because the input heat normally has a real financial cost, a memorable, generic definition of thermal efficiency is^[1]

ηth≡benefitcost.{displaystyle eta _{rm {th}}equiv {frac {text{benefit}}{text{cost}}}.}

From the first law of thermodynamics, the energy output cannot exceed the input (nor can it be equal), so

0≤ηth<1{displaystyle 0leq eta _{rm {th}}<1}

When expressed as a percentage, the thermal efficiency must be between 0% and 100%. Efficiency is typically less than 100% because there are inefficiencies such as friction and heat loss that convert the energy into alternative forms. For example, a typical gasoline automobile engine operates at around 25% efficiency, and a large coal-fuelled electrical generating plant peaks at about 46%, advances in Formula 1 motorsport regulations have pushed teams to develop highly efficient power units which peak around 45–50% thermal efficiency. The largest diesel engine in the world peaks at 51.7%. In a combined cycle plant, thermal efficiencies are approaching 60%.^[2] Such a real-world value may be used as a figure of merit for the device.

For engines where a fuel is burned there are two types of thermal efficiency: indicated thermal efficiency and brake thermal efficiency.^[3] This efficiency is only appropriate when comparing similar types or similar devices.

For other systems the specifics of the calculations of efficiency vary but the non dimensional input is still the same. Efficiency = Output energy / input energy

Heat engines

Heat engines transform thermal energy, or heat, Q_in into mechanical energy, or work, W_out. They cannot do this task perfectly, so some of the input heat energy is not converted into work, but is dissipated as waste heat Q_out into the environment

Qin=Wout+Qout{displaystyle Q_{in}=W_{rm {out}}+Q_{rm {out}},}

The thermal efficiency of a heat engine is the percentage of heat energy that is transformed into work. Thermal efficiency is defined as

ηth≡WoutQin=Qin−QoutQin=1−QoutQin{displaystyle eta _{rm {th}}equiv {frac {W_{rm {out}}}{Q_{rm {in}}}}={frac {{Q_{rm {in}}}-Q_{rm {out}}}{Q_{rm {in}}}}=1-{frac {Q_{rm {out}}}{Q_{rm {in}}}}}

The efficiency of even the best heat engines is low; usually below 50% and often far below. So the energy lost to the environment by heat engines is a major waste of energy resources, Since a large fraction of the fuels produced worldwide go to powering heat engines, perhaps up to half of the useful energy produced worldwide is wasted in engine inefficiency, although modern cogeneration, combined cycle and energy recycling schemes are beginning to use this heat for other purposes. This inefficiency can be attributed to three causes. There is an overall theoretical limit to the efficiency of any heat engine due to temperature, called the Carnot efficiency. Second, specific types of engines have lower limits on their efficiency due to the inherent irreversibility of the engine cycle they use. Thirdly, the nonideal behavior of real engines, such as mechanical friction and losses in the combustion process causes further efficiency losses.

Carnot efficiency

The second law of thermodynamics puts a fundamental limit on the thermal efficiency of all heat engines. Even an ideal, frictionless engine can't convert anywhere near 100% of its input heat into work. The limiting factors are the temperature at which the heat enters the engine, TH{displaystyle T_{rm {H}},}, and the temperature of the environment into which the engine exhausts its waste heat, TC{displaystyle T_{rm {C}},}, measured in an absolute scale, such as the Kelvin or Rankine scale. From Carnot's theorem, for any engine working between these two temperatures:^[4]

ηth≤1−TCTH{displaystyle eta _{rm {th}}leq 1-{frac {T_{rm {C}}}{T_{rm {H}}}},}

This limiting value is called the Carnot cycle efficiency because it is the efficiency of an unattainable, ideal, reversible engine cycle called the Carnot cycle. No device converting heat into mechanical energy, regardless of its construction, can exceed this efficiency.

Examples of TH{displaystyle T_{rm {H}},} are the temperature of hot steam entering the turbine of a steam power plant, or the temperature at which the fuel burns in an internal combustion engine. TC{displaystyle T_{rm {C}},} is usually the ambient temperature where the engine is located, or the temperature of a lake or river into which the waste heat is discharged. For example, if an automobile engine burns gasoline at a temperature of TH=816∘C=1500∘F=1089K{displaystyle T_{rm {H}}=816^{circ }{text{C}}=1500^{circ }{text{F}}=1089{text{K}},} and the ambient temperature is TC=21∘C=70∘F=294K{displaystyle T_{rm {C}}=21^{circ }{text{C}}=70^{circ }{text{F}}=294{text{K}},}, then its maximum possible efficiency is:

ηth≤(1−294K1089K)100%=73.0%{displaystyle eta _{rm {th}}leq left(1-{frac {294K}{1089K}}right)100%=73.0%}

It can be seen that since TC{displaystyle T_{rm {C}},} is fixed by the environment, the only way for a designer to increase the Carnot efficiency of an engine is to increase TH{displaystyle T_{rm {H}},}, the temperature at which the heat is added to the engine. The efficiency of ordinary heat engines also generally increases with operating temperature, and advanced structural materials that allow engines to operate at higher temperatures is an active area of research.

Due to the other causes detailed below, practical engines have efficiencies far below the Carnot limit. For example, the average automobile engine is less than 35% efficient.

Carnot's theorem applies to thermodynamic cycles, where thermal energy is converted to mechanical work. Devices that convert a fuel's chemical energy directly into electrical work, such as fuel cells, can exceed the Carnot efficiency.
^[5][6]

Engine cycle efficiency

The Carnot cycle is reversible and thus represents the upper limit on efficiency of an engine cycle. Practical engine cycles are irreversible and thus have inherently lower efficiency than the Carnot efficiency when operated between the same temperatures TH{displaystyle T_{rm {H}},} and TC{displaystyle T_{rm {C}},}. One of the factors determining efficiency is how heat is added to the working fluid in the cycle, and how it is removed. The Carnot cycle achieves maximum efficiency because all the heat is added to the working fluid at the maximum temperature TH{displaystyle T_{rm {H}},}, and removed at the minimum temperature TC{displaystyle T_{rm {C}},}. In contrast, in an internal combustion engine, the temperature of the fuel-air mixture in the cylinder is nowhere near its peak temperature as the fuel starts to burn, and only reaches the peak temperature as all the fuel is consumed, so the average temperature at which heat is added is lower, reducing efficiency.

An important parameter in the efficiency of combustion engines is the specific heat ratio of the air-fuel mixture, γ. This varies somewhat with the fuel, but is generally close to the air value of 1.4. This standard value is usually used in the engine cycle equations below, and when this approximation is made the cycle is called an air-standard cycle.

• 
  Otto cycle: automobiles The Otto cycle is the name for the cycle used in spark-ignition internal combustion engines such as gasoline and hydrogen fuelled automobile engines. Its theoretical efficiency depends on the compression ratio r of the engine and the specific heat ratio γ of the gas in the combustion chamber.^[4]:558
  

ηth=1−1rγ−1{displaystyle eta _{rm {th}}=1-{frac {1}{r^{gamma -1}}},}

Thus, the efficiency increases with the compression ratio. However the compression ratio of Otto cycle engines is limited by the need to prevent the uncontrolled combustion known as knocking. Modern engines have compression ratios in the range 8 to 11, resulting in ideal cycle efficiencies of 56% to 61%.

• 
  Diesel cycle: trucks and trains In the Diesel cycle used in diesel truck and train engines, the fuel is ignited by compression in the cylinder. The efficiency of the Diesel cycle is dependent on r and γ like the Otto cycle, and also by the cutoff ratio, r_c, which is the ratio of the cylinder volume at the beginning and end of the combustion process:^[4]
  

ηth=1−r1−γ(rcγ−1)γ(rc−1){displaystyle eta _{rm {th}}=1-{frac {r^{1-gamma }(r_{rm {c}}^{gamma }-1)}{gamma (r_{rm {c}}-1)}},}

The Diesel cycle is less efficient than the Otto cycle when using the same compression ratio. However, practical Diesel engines are 30% - 35% more efficient than gasoline engines.^[7] This is because, since the fuel is not introduced to the combustion chamber until it is required for ignition, the compression ratio is not limited by the need to avoid knocking, so higher ratios are used than in spark ignition engines.

• 
  Rankine cycle: steam power plants The Rankine cycle is the cycle used in steam turbine power plants. The overwhelming majority of the world's electric power is produced with this cycle. Since the cycle's working fluid, water, changes from liquid to vapor and back during the cycle, their efficiencies depend on the thermodynamic properties of water. The thermal efficiency of modern steam turbine plants with reheat cycles can reach 47%, and in combined cycle plants, in which a steam turbine is powered by exhaust heat from a gas turbine, it can approach 60%.^[4]
  


• 
  Brayton cycle: gas turbines and jet engines The Brayton cycle is the cycle used in gas turbines and jet engines. It consists of a compressor that increases pressure of the incoming air, then fuel is continuously added to the flow and burned, and the hot exhaust gasses are expanded in a turbine. The efficiency depends largely on the ratio of the pressure inside the combustion chamber p₂ to the pressure outside p₁^[4]
  

ηth=1−(p2p1)1−γγ{displaystyle eta _{rm {th}}=1-{bigg (}{frac {p_{2}}{p_{1}}}{bigg )}^{frac {1-gamma }{gamma }},}

Other inefficiencies

The above efficiency formulas are based on simple idealized mathematical models of engines, with no friction and working fluids that obey simple thermodynamic rules called the ideal gas law. Real engines have many departures from ideal behavior that waste energy, reducing actual efficiencies far below the theoretical values given above. Examples are:

• 
  friction of moving parts


• inefficient combustion


• heat loss from the combustion chamber


• departure of the working fluid from the thermodynamic properties of an ideal gas
  


• aerodynamic drag of air moving through the engine


• energy used by auxiliary equipment like oil and water pumps.


• inefficient compressors and turbines


• imperfect valve timing

Another source of inefficiency is that engines must be optimized for other goals besides efficiency, such as low pollution. The requirements for vehicle engines are particularly stringent: they must be designed for low emissions, adequate acceleration, fast starting, light weight, low noise, etc. These require compromises in design (such as altered valve timing to reduce emissions) that reduce efficiency. The average automobile engine is only about 35% efficient, and must also be kept idling at stoplights, wasting an additional 17% of the energy, resulting in an overall efficiency of 18%.^[7] Large stationary electric generating plants have fewer of these competing requirements as well as more efficient Rankine cycles, so they are significantly more efficient than vehicle engines, around 50%. Therefore, replacing internal combustion vehicles with electric vehicles, which run on a battery that is charged with electricity generated by burning fuel in a power plant, has the theoretical potential to increase the thermal efficiency of energy use in transportation, thus decreasing the demand for fossil fuels.

When comparing different heat engines as sources of power, such as electric power or the power to run vehicles, the engine efficiency alone is only one factor. To give a meaningful comparison, the overall efficiency of the entire energy supply chain from the fuel source to the consumer must be considered. Although the heat wasted by heat engines is usually the largest source of inefficiency, factors such as the energy cost of fuel refining and transportation, and energy loss in electrical transmission lines to transport it, may offset the advantage of a more efficient heat engine.

Energy conversion

For a device that converts energy from another form into thermal energy (such as an electric heater, boiler, or furnace), the thermal efficiency is

ηth≡QoutQin{displaystyle eta _{rm {th}}equiv {frac {Q_{rm {out}}}{Q_{rm {in}}}}}

where the Q{displaystyle Q} quantities are heat-equivalent values.

So, for a boiler that produces 210 kW (or 700,000 BTU/h) output for each 300 kW (or 1,000,000 BTU/h) heat-equivalent input, its thermal efficiency is 210/300 = 0.70, or 70%. This means that 30% of the energy is lost to the environment.

An electric resistance heater has a thermal efficiency close to 100%.^[8] When comparing heating units, such as a highly efficient electric resistance heater to an 80% efficient natural gas-fuelled furnace, an economic analysis is needed to determine the most cost-effective choice.

Effects of fuel heating value

The heating value of a fuel is the amount of heat released during an exothermic reaction (e.g., combustion) and is a characteristic of each substance. It is measured in units of energy per unit of the substance, usually mass, such as: kJ/kg, J/mol.

The heating value for fuels is expressed as the HHV, LHV, or GHV to distinguish treatment of the heat of phase changes:

• 
  Higher heating value (HHV) is determined by bringing all the products of combustion back to the original pre-combustion temperature, and in particular condensing any vapor produced. This is the same as the thermodynamic heat of combustion.


• 
  Lower heating value (LHV) (or net calorific value) is determined by subtracting the heat of vaporization of the water vapor from the higher heating value. The energy required to vaporize the water therefore is not realized as heat.


• 
  Gross heating value accounts for water in the exhaust leaving as vapor, and includes liquid water in the fuel prior to combustion. This value is important for fuels like wood or coal, which will usually contain some amount of water prior to burning.

Which definition of heating value is being used significantly affects any quoted efficiency. Not stating whether an efficiency is HHV or LHV renders such numbers very misleading.

Heat pumps and refrigerators

Heat pumps, refrigerators and air conditioners use work to move heat from a colder to a warmer place, so their function is the opposite of a heat engine. The work energy (W_in) that is applied to them is converted into heat, and the sum of this energy and the heat energy that is moved from the cold reservoir (Q_C) is equal to the total heat energy added to the hot reservoir (Q_H)

QH=QC+Win{displaystyle Q_{rm {H}}=Q_{rm {C}}+W_{rm {in}},}

Their efficiency is measured by a coefficient of performance (COP). Heat pumps are measured by the efficiency with which they add heat to the hot reservoir, COP_heating; refrigerators and air conditioners by the efficiency with which they remove heat from the cold interior, COP_cooling:

COPheating≡QHWin{displaystyle mathrm {COP} _{mathrm {heating} }equiv {frac {Q_{rm {H}}}{W_{rm {in}}}},}

COPcooling≡QCWin{displaystyle mathrm {COP} _{mathrm {cooling} }equiv {frac {Q_{rm {C}}}{W_{rm {in}}}},}

The reason the term "coefficient of performance" is used instead of "efficiency" is that, since these devices are moving heat, not creating it, the amount of heat they move can be greater than the input work, so the COP can be greater than 1 (100%). Therefore, heat pumps can be a more efficient way of heating than simply converting the input work into heat, as in an electric heater or furnace.

Since they are heat engines, these devices are also limited by Carnot's theorem. The limiting value of the Carnot 'efficiency' for these processes, with the equality theoretically achievable only with an ideal 'reversible' cycle, is:

COPheating≤THTH−TC=COPheating,carnot{displaystyle mathrm {COP} _{mathrm {heating} }leq {frac {T_{rm {H}}}{T_{rm {H}}-T_{rm {C}}}}=mathrm {COP} _{mathrm {heating,carnot} }}

COPcooling≤TCTH−TC=COPcooling,carnot{displaystyle mathrm {COP} _{mathrm {cooling} }leq {frac {T_{rm {C}}}{T_{rm {H}}-T_{rm {C}}}}=mathrm {COP} _{mathrm {cooling,carnot} }}

The same device used between the same temperatures is more efficient when considered as a heat pump than when considered as a refrigerator:

COPheating−COPcooling=1{displaystyle mathrm {COP} _{mathrm {heating} }-mathrm {COP} _{mathrm {cooling} }=1,}

This is because when heating, the work used to run the device is converted to heat and adds to the desired effect, whereas if the desired effect is cooling the heat resulting from the input work is just an unwanted by-product. Sometimes, the term efficiency is used for the ratio of the achieved COP to the Carnot COP, which can not exceed 100%.^[9]

Energy efficiency

The 'thermal efficiency' is sometimes called the energy efficiency. In the United States, in everyday usage the SEER is the more common measure of energy efficiency for cooling devices, as well as for heat pumps when in their heating mode. For energy-conversion heating devices their peak steady-state thermal efficiency is often stated, e.g., 'this furnace is 90% efficient', but a more detailed measure of seasonal energy effectiveness is the annual fuel use efficiency (AFUE).^[10]

Energy efficiency of heat exchangers

A counter flow heat exchanger is the most efficient type of heat exchanger in transferring heat energy from one circuit to the other. However, for a more complete picture of heat exchanger efficiency, exergetic considerations must be taken into account.thermal efficiency in ic engine is higher than ec engine.

See also

• Kalina cycle


• Electrical efficiency


• Mechanical efficiency


• Heat engine


• 
  Federal roofing tax credit for energy efficiency (US)


• Lower heating value


• Relative cost of electricity generated by different sources


• Higher heating value


• Energy conversion efficiency

References